When a property manager gets a call from a tenant about dead outlets in a unit, or a builder needs a circuit run before the inspection window closes, the job lands with us. Altadena has a mix of older residential stock and established neighborhoods where the wiring has history, and that history shows up in the work: panels that have been added to over the decades, circuits that were extended without documentation, and two-prong outlets that signal a grounding story nobody has finished telling. We scope those jobs on the phone, give you a price before anything is scheduled, and take calls any hour of the day or night.
Calls are answered here, and the work gets scheduled properly. Whether the call comes from a property owner dealing with a recurring fault or a contractor who needs the electrical side finished before the next trade walks in, we handle it the same way: the fault traced before anything is replaced, and clear communication from the first call to the final test. We are available around the clock, seven days a week, including weekends and holidays.
Older homes carry their electrical history in layers. A house that was built decades ago and has had work done at intervals often has wiring that mixes generations: original knob-and-tube in the walls alongside a partial rewire from the eighties and a panel that was swapped out sometime in between. The symptoms that show up in a place like this are specific.
A breaker that trips when two things run at once is not a breaker problem. It is a load problem, and the fix is a circuit sized for what the room actually demands. We add dedicated circuits for new appliances, hot tubs, and workshop equipment, running the right wire gauge from the panel to the point of use and confirming the panel has capacity before we start. If it does not, that conversation happens on the call, not after we have opened the wall.
Weatherproof outdoor outlets and enclosures are part of the same conversation for a lot of Altadena properties. An exterior outlet that is not properly rated for outdoor use, or one that has no GFCI protection near a water source, is a fault waiting to happen. We install and replace outdoor receptacles with the right enclosures and protection for the location.
Hardwired smoke and carbon monoxide alarms are required in California residential properties, and the interconnected kind, where one alarm triggers all of them, requires wiring that a battery-only unit does not. We install and replace hardwired alarms, confirm the interconnect is working, and make sure the placement meets what the code cycle for the property requires.
Ceiling fan installation and replacement come up regularly in homes where a light fixture is the only thing on the box. Running a fan on a box that was not rated for one is a problem, and adding a separate control for the light kit when the existing switch only has one leg is a wiring job, not a swap. We confirm what the box and the circuit can support before the fan goes up.
Knob-and-tube replacement and aluminum branch-circuit wiring remediation are jobs we handle in full. Knob-and-tube is not automatically dangerous, but it was not designed for the loads a modern household puts on it, and it cannot be extended or covered with insulation safely. Aluminum wiring at device connections is a different problem: the connections loosen over time and the metal oxidizes in a way that creates heat. Both situations get a straight assessment and a clear explanation of what the repair involves before any work is proposed.
An electrical safety inspection is the right starting point when the wiring history of a property is unclear. It gives a complete picture of what is there, what meets current code, and what needs attention. We tell you if a permit is needed. We name the fault plainly. You decide the fix.
Scheduling a service call is simple, and the process is the same whether the job is urgent or planned. You call, describe what you are dealing with, and we ask the questions that let us scope the job on the phone. The price is confirmed before we book the visit. You know what it covers, and there is no obligation to proceed.
For a fault that will not keep, we take calls any hour. A burning smell near a panel, an outlet that is warm to the touch, a breaker that will not reset: these are urgent calls, and they are answered on nights, weekends, and holidays the same as any other day. There are no closed hours and no after-hours rate to navigate.
For tenants and businesses that have to stay operational, we work around the schedule. If a unit is occupied or a space cannot go dark during business hours, we confirm what the job requires and plan around it on the call. The scope and the timing are settled before anyone shows up.
When we open a wall or a panel and find wiring that does not match what the permit history says, or connections that were made in ways that do not meet code, we assess it the same way we assess anything else: what is the actual condition, what does it affect, and what does a proper correction involve.
Not everything that looks non-standard is a hazard. Some of it is older work that was correct when it was done. Some of it is work that was done wrong and needs to come out. We tell you which is which, explain what the correction involves, and let you decide how to proceed. No pressure to expand the job beyond what the situation calls for. No-pressure estimates, priced up front, is how every call runs.
Where a panel has been added to over the years without a consistent hand on it, or where a subpanel was installed without the grounding and bonding it needed, those are corrections we can make properly. Panel upgrades, service-entrance work, and meter base replacement are part of the scope when the existing infrastructure cannot carry what the property needs. Before booking anything, the full electrical services list is worth a read.
Commercial and light industrial properties in Altadena have a different set of priorities than a residential job. A retail space or a professional office cannot afford a full-day outage for electrical work, and a property manager with multiple units needs the job planned so that only the affected circuit goes down, not the whole building.
We plan commercial jobs around the operation. That means confirming which circuits feed which areas before anything is disconnected, scheduling work that affects common areas or shared panels outside peak hours where possible, and keeping the scope tight so the disruption is as short as the job allows. Out-of-hours work is available any day of the week.
Dedicated circuit installation for commercial equipment, panel capacity assessments before a tenant improvement, and recessed and LED lighting upgrades are all jobs we handle on the commercial side. Whole-home surge protection at the panel level applies to commercial properties too, and in a region where grid fluctuations during high-demand periods are a real factor, it is worth adding when the panel is already open.
The price for an electrical job depends on what the job actually involves. The fault and where it sits in the circuit, what has to be opened up to reach it, and whether the existing panel can carry the change are the things that move the number. We give you the rate on the phone based on what you describe, and we confirm it before the visit is booked.
If the scope changes once we are on site, because a wall reveals something the phone call could not, the price is reset before we proceed, not after. You get a straight answer about what changed and what it costs to correct it. What we quote is based on the work, not on the size of the property.
Getting a quote costs nothing.
Call (818) 369-3955 and we will walk through it with you.
We cover Altadena and the surrounding communities across Los Angeles County, including Pasadena, La Canada Flintridge, San Pasqual, San Marino, and East Pasadena. Any of those calls come in the same way and get the same response: scoped on the phone, priced before it is scheduled, and handled any day of the week.
If you are in the area and unsure whether we cover your address, call and ask. We will tell you on the spot.
We scope the job on the call and confirm what can be completed within the available window. Straightforward repairs, outlet replacements, and panel work can usually be scheduled and completed within a short turnaround. If the scope is larger, we prioritize the items that affect habitability and plan any remaining work around the new tenancy.
A high ceiling requires access equipment to reach the fixture location safely. We confirm the ceiling height and the access situation on the call so the visit is set up correctly. If the ceiling is unusually high, let us know when you call so we can confirm what the job requires.
An outlet that works sometimes and not others usually has a loose connection at the device, at a junction box upstream, or at the panel. Intermittent faults can be harder to reproduce during a diagnostic, which is why noting when the fault occurs and what is plugged in at the time is useful. We trace the connection back through the circuit to find where the contact is failing.
Do not attempt to extend or modify it yourself. Call us and describe what you are seeing. We can often get a sense of the situation on the phone, and an electrical safety inspection gives a full picture of the wiring condition and what it needs. Some older work is code-compliant for the era it was done in. Some of it is not. We tell you which is which before anything is scheduled.
A temporary supply involves running a circuit from the existing panel or a temporary panel to provide power to the work area during the renovation. We scope what the temporary supply needs to carry, confirm the panel can support it, and install it in a way that does not interfere with the permanent work that follows.
Good electrical work isn't complicated, it's just done right, and that applies to a single outlet as much as it does to a full service upgrade. A loose connection that causes a dead receptacle, a ceiling fan that wobbles on a box that was not rated for it, a smoke alarm that needs to be hardwired into the circuit: none of these are too small to call about, and none of them get smaller by waiting.
Call (818) 369-3955 any time of day or night.
We take the call, scope the job, and give you a price before anything is scheduled. The first step is the phone call, and that part is always simple.
Electrical service reaches these neighboring areas too: Pasadena, Glendale, La Crescenta-Montrose, Burbank, Sun Valley.
Every electrical job we take starts the same way: you call, we scope the work on the phone, and you get a price before anything is scheduled. The table below covers the services we offer across Altadena and the San Fernando Valley, who each one is built for, and what is worth knowing before you book. If a service is not listed or you are not sure what your situation calls for, call us and we will tell you plainly what the job involves.
| Service Type | Scope of Work | Best For | What to Keep in Mind |
|---|---|---|---|
| Lighting Installation | Recessed and under-cabinet lightingPendant and flush-mount fixturesExterior and security lightingMotion sensor and landscape lighting | Homeowners upgrading interior lighting or adding outdoor lighting for security or year-round use | Southern California's climate makes outdoor lighting a year-round job. We weatherproof all exterior connections and run circuits to handle the placement properly. |
| Hot-Tub Circuits | Dedicated 240V circuit from panelGFCI protection at disconnectBonding for water-adjacent equipmentPermit and inspection coordination | Homeowners installing or relocating a hot tub or spa in Los Angeles County | Hot-tub wiring involves bonding requirements and GFCI protection specific to proximity to water. We handle the full electrical scope, from the panel to the equipment pad. |
| Electrical Panel Upgrades | Panel replacement and service upgradesSubpanel installationLoad calculations before upgradePermit and inspection coordination | Homes adding major appliances, EV chargers, or solar, and properties with aging or undersized panels | Panel work in Los Angeles County requires a permit and inspection. We confirm what applies to your address and coordinate that process before the job is scheduled. |
Call (818) 369-3955 and we will scope the job on the phone, give you a price before anything is scheduled, and get the work done right.
(818) 369-3955